Новый Claymore’s NeoScrypt AMD GPU Miner v1.0 — SB5 TV

Новый Claymore’s NeoScrypt AMD GPU Miner v1.0

ПРЕДУПРЕЖДЕНИЕ: Алгоритм NeoScrypt ОЧЕНЬ ГОРЯЧИЙ, убедитесь, что у вас мощный PSU и хорошее охлаждение графического процессора, используйте опцию «-powlim 50», чтобы получить полный хэш-сигнал.

 

Это версия POOL. Используйте последние драйверы. Для майнинга требуется до 1,1 ГБ памяти GPU.
Для систем с несколькими GPU установите размер виртуальной памяти в Windows не менее 16 ГБ

Этот майнер поддерживает только самые популярные чипы AMD GPU: Pitcairn, Tahiti, Hawaii, Tonga, Fiji, Ellesmere, Baffin, Vega.
В настоящее время поддерживается только Windows x64. Нет поддержки Linux. Нет 32-разрядной поддержки.
Поддержка NVidia не поддерживается.

В архиве есть примеры BAT-файлов на разные маетны по NeoScrypt  от SB5 TV

Скачать майнер:

 

Этот майнер является бесплатным, однако текущая плата за разработчика составляет 2%, каждый час работает 72 секунды для разработчика.
Если вы не согласны с вознаграждением разработчика — не используйте этот майнер или не используйте опцию «-nofee 1».

 

Команды на английском:

-pool    NeoScrypt pool address. Only Stratum protocol is supported.

-wal    Your wallet address. Also worker name and other options if pool supports it.

-psw    Password for NeoScrypt pool, use «x» as password, and/or any other options if pool supports them.

-a   algorithm mode for Ellesmere cards (RX470/RX480/RX570/RX580 cards), for other cards always «-a 1» is used. You can specify «-a 1» (default) or «-a 2» and find the best hashrate for your card.
You can also set this option for every card individually, for example «-a 1,2,1».

-di    GPU indexes, default is all available GPUs. For example, if you have four GPUs «-di 02» will enable only first and third GPUs (#0 and #2).
You can also turn on/off cards in runtime with «0»…»9″ keys and check current statistics with «s» key.
For systems with more than 10 GPUs: use letters to specify indexes more than 9, for example, «a» means index 10, «b» means index 11, etc; also «a», «b», and «c» keys allow you to turn on/off GPU #10, #11 and #12 in runtime.

-ftime   failover main pool switch time, in minutes, see «Failover» section below. Default value is 30 minutes, set zero if there is no main pool.

-wd    watchdog option. Default value is «-wd 1», it enables watchdog, miner will be closed (or restarted, see «-r» option) if any thread is not responding for 1 minute or OpenCL call failed.
Specify «-wd 0» to disable watchdog.

-r   Restart miner mode. «-r 0» (default) — restart miner if something wrong with GPU. «-r -1» — disable automatic restarting. -r >20 — restart miner if something
wrong with GPU or by timer. For example, «-r 60» — restart miner every hour or when some GPU failed.
«-r 1» closes miner and execute «reboot.bat» file («reboot.bash» or «reboot.sh» for Linux version) in the miner directory (if exists) if some GPU failed.
So you can create «reboot.bat» file and perform some actions, for example, reboot system if you put this line there: «shutdown /r /t 5 /f».

-minspeed   minimal speed, in KH/s. If miner cannot reach this speed for 5 minutes for any reason, miner will be restarted (or «reboot.bat» will be executed if «-r 1» is set). Default value is 0 (feature disabled).
You can also specify negative values if you don’t want to restart miner due to pool connection issues; for example, «-minspeed -3000» will restart miner only if it cannot reach 3Mh/s at good pool connection.

-retrydelay   delay, in seconds, between connection attempts. Default values is «20». Specify «-retrydelay -1» if you don’t need reconnection, in this mode miner will exit if connection is lost.

-dbg   debug log and messages. «-dbg 0» — (default) create log file but don’t show debug messages.
«-dbg 1» — create log file and show debug messages. «-dbg -1» — no log file and no debug messages.

-logfile   debug log file name. After restart, miner will append new log data to the same file. If you want to clear old log data, file name must contain «noappend» string.
If missed, default file name will be used.

-logsmaxsize   maximal size of debug log files, in MB. At every start the miner checks all files in its folder, selects all files that contain «_log.txt» string and removes oldest files if summary files size is larger than specified value.
Specify «-logsmaxsize 0» to cancel old logs removal. Default value is 1000 (i.e. about 1GB of log files are allowed).

-nofee   set «1» to cancel my developer fee at all. In this mode some optimizations are disabled so mining speed will be slower by about 5%.
By enabling this mode, I will lose 100% of my earnings, you will lose only 3% of your earnings.
So you have a choice: «fastest miner» or «completely free miner but a bit slower».
If you want both «fastest» and «completely free» you should find some other miner that meets your requirements, just don’t use this miner instead of claiming that I need
to cancel/reduce developer fee, saying that 2% developer fee is too much for this miner and so on.

-benchmark   benchmark mode, specify «-benchmark 1» to see hashrate for your hardware.

-li   low intensity mode. Reduces mining intensity, useful if your cards are overheated. Note that mining speed is reduced too.
More value means less heat and mining speed, for example, «-li 10» is less heat and mining speed than «-li 1». You can also specify values for every card, for example «-li 3,10,50».
Default value is «0» — no low intensity mode.

-tt   set target GPU temperature. For example, «-tt 80» means 80C temperature. You can also specify values for every card, for example «-tt 70,80,75».
You can also set static fan speed if you specify negative values, for example «-tt -50» sets 50% fan speed. Specify zero to disable control and hide GPU statistics.
«-tt 1» (default) does not manage fans but shows GPU temperature and fan status every 30 seconds. Specify values 2..5 if it is too often.

-ttli   reduce entire mining intensity (for all coins) automatically if GPU temperature is above specified value. For example, «-ttli 80» reduces mining intensity if GPU temperature is above 80C.
You can see if intensity was reduced in detailed statistics («s» key).
You can also specify values for every card, for example «-ttli 80,85,80». You also should specify non-zero value for «-tt» option to enable this option.
It is a good idea to set «-ttli» value higher than «-tt» value by 3-5C.

-tstop   set stop GPU temperature, miner will stop mining if GPU reaches specified temperature. For example, «-tstop 95» means 95C temperature. You can also specify values for every card, for example «-tstop 95,85,90».
This feature is disabled by default («-tstop 0»). You also should specify non-zero value for «-tt» option to enable this option.
If it turned off wrong card, it will close miner in 30 seconds.
You can also specify negative value to close miner immediately instead of stopping GPU, for example, «-tstop -95» will close miner as soon as any GPU reach 95C temperature.

-fanmax   set maximal fan speed, in percents, for example, «-fanmax 80» will set maximal fans speed to 80%. You can also specify values for every card, for example «-fanmax 50,60,70».
This option works only if miner manages cooling, i.e. when «-tt» option is used to specify target temperature. Default value is «100».

-fanmin   set minimal fan speed, in percents, for example, «-fanmin 50» will set minimal fans speed to 50%. You can also specify values for every card, for example «-fanmin 50,60,70».
This option works only if miner manages cooling, i.e. when «-tt» option is used to specify target temperature. Default value is «0».

-cclock   set target GPU core clock speed, in MHz. If not specified or zero, miner will not change current clock speed. You can also specify values for every card, for example «-cclock 1000,1050,1100,0».
Note: for some drivers versions AMD blocked underclocking for some reason, you can overclock only.
Note: this option changes clocks for all power states, so check voltage for all power states in WattMan or use -cvddc option.
By default, low power states have low voltage, setting high GPU clock for low power states without increasing voltage can cause driver crash.

-mclock   set target GPU memory clock speed, in MHz. If not specified or zero, miner will not change current clock speed. You can also specify values for every card, for example «-mclock 1200,1250,1200,0».
Note: for some drivers versions AMD blocked underclocking for some reason, you can overclock only.

-powlim set power limit, from -50 to 50. If not specified, miner will not change power limit. You can also specify values for every card, for example «-powlim 20,-20,0,10».

-cvddc   set target GPU core voltage, multiplied by 1000. For example, «-cvddc 1050» means 1.05V. You can also specify values for every card, for example «-cvddc 900,950,1000,970». Supports latest AMD 4xx cards only in Windows.

-mvddc   set target GPU memory voltage, multiplied by 1000. For example, «-mvddc 1050» means 1.05V. You can also specify values for every card, for example «-mvddc 900,950,1000,970». Supports latest AMD 4xx cards only in Windows.

-mport   remote monitoring/management port. Default value is -3333 (read-only mode), specify «-mport 0» to disable remote monitoring/management feature.
Specify negative value to enable monitoring (get statistics) but disable management (restart, uploading files), for example, «-mport -3333» enables port 3333 for remote monitoring, but remote management will be blocked.
You can also use your web browser to see current miner state, for example, type «localhost:3333» in web browser.
Warning: use negative option value or disable remote management entirely if you think that you can be attacked via this port!
By default, miner will accept connections on specified port on all network adapters, but you can select desired network interface directly, for example, «-mport 127.0.0.1:3333» opens port on localhost only.

-mpsw   remote monitoring/management password. By default it is empty, so everyone can ask statistics or manage miner remotely if «-mport» option is set. You can set password for remote access (at least EthMan v3.0 is required to support passwords).

-colors enables or disables colored text in console. Default value is «1», use «-colors 0» to disable coloring. Use 2…4 values to remove some of colors.

-v   displays miner version, sample usage: «-v 1».